Post Reply 
I can't afford a HP-19C so I bought this instead
04-20-2016, 03:24 AM (This post was last modified: 04-20-2016 03:59 AM by Francois Lanciault.)
Post: #1
I can't afford a HP-19C so I bought this instead
The canon FP-11P !

Beside the HP-19C, it is the only other scientific, programable, pocket calculator with embedded printer in the world! (if I exclude some pocket basic computers, not the same as calculator in my mind)

It is nowhere as good as the HP-19C as it only have 45 partly merged steps, 7 memories and other serious limitations. It is a printing version of the FP-73P. But its big advantage is the cost: 10 bucks on Ebay! I was lucky as they don't come about very often.

It is in good condition but the printer, while printing clear characters have a tendency to stick at the end of the print line and thus print all remaining digits ion top of each other. I will open it and try to fix the printer. When I do so, I will post pictures of the calculator guts.

Meanwhile, here is a picture taken from google:

[Image: 8623aee7a94a8869db3a367b78b1fb3b.jpg]

Is there anybody with experience servicing this calculator ?

François
Find all posts by this user
Quote this message in a reply
04-20-2016, 05:22 AM
Post: #2
RE: I can't afford a HP-19C so I bought this instead
No to your question, but would the printer mechanism fit in a card reader housing ??

[bwa, ha, ha, ha, ha !!!]

2speed HP41CX,int2XMEM+ZEN, HPIL+DEVEL, HPIL+X/IO, I/R, 82143, 82163, 82162 -25,35,45,55,65,67,70,80
Find all posts by this user
Quote this message in a reply
04-21-2016, 03:22 AM
Post: #3
RE: I can't afford a HP-19C so I bought this instead
(04-20-2016 05:22 AM)TASP Wrote:  No to your question, but would the printer mechanism fit in a card reader housing ??

[bwa, ha, ha, ha, ha !!!]

It is certainly small enough to fit...
Find all posts by this user
Quote this message in a reply
04-21-2016, 04:09 AM
Post: #4
RE: I can't afford a HP-19C so I bought this instead
I just can't get an HP41 card reader housing with a printer in it out of my mind.

As for the opening post, hope just cleaning it out is all it takes to get it working right. Maybe a little grease, and checking for any material deterioration issues . . . .

2speed HP41CX,int2XMEM+ZEN, HPIL+DEVEL, HPIL+X/IO, I/R, 82143, 82163, 82162 -25,35,45,55,65,67,70,80
Find all posts by this user
Quote this message in a reply
04-22-2016, 03:46 PM
Post: #5
RE: I can't afford a HP-19C so I bought this instead
(04-21-2016 04:09 AM)TASP Wrote:  I just can't get an HP41 card reader housing with a printer in it out of my mind.

As for the opening post, hope just cleaning it out is all it takes to get it working right. Maybe a little grease, and checking for any material deterioration issues . . . .

That brings back the vivid memory of the announcement of the 19C and sincerely hoping that this calculator contained a built-in card reader like the 65/67. No such luck, unfortunately.

Jake
Find all posts by this user
Quote this message in a reply
04-22-2016, 04:00 PM
Post: #6
RE: I can't afford a HP-19C so I bought this instead
lol, bad enough I covet an HP41 accessory never made, and you suggest a better one.

A card reader housing with a printer in it, that still can read cards !!!

OMG !!!!

I gotta get me a 3D printer . . . .

2speed HP41CX,int2XMEM+ZEN, HPIL+DEVEL, HPIL+X/IO, I/R, 82143, 82163, 82162 -25,35,45,55,65,67,70,80
Find all posts by this user
Quote this message in a reply
04-22-2016, 04:12 PM
Post: #7
RE: I can't afford a HP-19C so I bought this instead
(04-22-2016 04:00 PM)TASP Wrote:  lol, bad enough I covet an HP41 accessory never made, and you suggest a better one.

A card reader housing with a printer in it, that still can read cards !!!

OMG !!!!

I gotta get me a 3D printer . . . .

Perhaps if they had gone back, following the introduction of the 75C, and redid the 41 card reader to be a hand-pulled version, the removal of the motor might have left room for some other goodies :-) I suppose hand-pulling cards as short as those would be impractical.

Jake
Find all posts by this user
Quote this message in a reply
04-22-2016, 05:09 PM
Post: #8
RE: I can't afford a HP-19C so I bought this instead
The coolness factor of having a motor is significant too.

2speed HP41CX,int2XMEM+ZEN, HPIL+DEVEL, HPIL+X/IO, I/R, 82143, 82163, 82162 -25,35,45,55,65,67,70,80
Find all posts by this user
Quote this message in a reply
04-22-2016, 05:11 PM
Post: #9
RE: I can't afford a HP-19C so I bought this instead
Have a read head next to the print head over the platen to read the cards ??

(Hope they can bend that tight)

Smile

2speed HP41CX,int2XMEM+ZEN, HPIL+DEVEL, HPIL+X/IO, I/R, 82143, 82163, 82162 -25,35,45,55,65,67,70,80
Find all posts by this user
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 2 Guest(s)