Post Reply 
pyILPER Version 1.3.4 released
08-29-2016, 09:48 AM
Post: #7
RE: pyILPER Version 1.3.4 released
(08-28-2016 09:43 PM)dayd Wrote:  The printer was of course enabled and I’ve got ‘only’ a HP-41CX as controller but your hint was good as I pursued it with the following commands: MANIO, 3 SELECT (the third device in the loop being the printer), PRA and voilà, it worked. Back to AUTOIO mode it still works.
I was assuming that each time I unplug/plug the 82160A HP-IL Module, the system was back to his default state (?). I don’t have other HP-IL special module, like Extended IO to investigate further what’s really going on.

The MANIO/AUTOIO status is kept in the flag 32 of the HP-41C, but the selected device is kept in the HP-IL module. So unplug/plug the HP-IL resets the selected device to 1, while possibly still in MANIO.
With the HP-41C, I recommend to use AUTOIO as much as possible, unless for special needs.
I also chose (in the original ILPer) to put the printer as the first device, for this kind of reason.

J-F
Visit this user's website Find all posts by this user
Quote this message in a reply
Post Reply 


Messages In This Thread
pyILPER Version 1.3.4 released - jsi - 08-27-2016, 06:07 PM
RE: pyILPER Version 1.3.4 released - dayd - 08-28-2016, 01:29 PM
RE: pyILPER Version 1.3.4 released - jsi - 08-28-2016, 04:53 PM
RE: pyILPER Version 1.3.4 released - dayd - 08-28-2016, 09:43 PM
RE: pyILPER Version 1.3.4 released - J-F Garnier - 08-29-2016 09:48 AM
RE: pyILPER Version 1.3.4 released - dayd - 08-30-2016, 02:40 PM
RE: pyILPER Version 1.3.4 released - jsi - 10-04-2016, 10:53 AM
RE: pyILPER Version 1.3.4 released - jsi - 10-04-2016, 01:47 PM
RE: pyILPER Version 1.3.4 released - jsi - 10-06-2016, 06:21 PM
RE: pyILPER Version 1.3.4 released - jch - 12-18-2016, 09:42 PM
RE: pyILPER Version 1.3.4 released - jch - 12-19-2016, 07:52 PM
RE: pyILPER Version 1.3.4 released - jch - 12-20-2016, 10:08 PM
RE: pyILPER Version 1.3.4 released - Erwin - 01-04-2017, 07:31 PM
RE: pyILPER Version 1.3.4 released - jsi - 01-16-2017, 12:25 PM
RE: pyILPER Version 1.3.4 released - Erwin - 01-16-2017, 06:53 PM
RE: pyILPER Version 1.3.4 released - Erwin - 01-11-2017, 09:42 PM
RE: pyILPER Version 1.3.4 released - dayd - 01-11-2017, 10:31 PM
RE: pyILPER Version 1.3.4 released - Erwin - 01-12-2017, 06:20 AM



User(s) browsing this thread: 1 Guest(s)