Post Reply 
(32SII) Glide Slope Calculations
08-14-2023, 02:42 AM
Post: #1
(32SII) Glide Slope Calculations
Introduction

The following program calculates the forces and angle for a flight of a glider, an aircraft without a engine:

* Weight
* Lift Force
* Drag Force

SI units are used.

With inputs glide distance (G), height (H), and mass (M):

Angle: A = arcsin(H ÷ G)

Weight: W = M × 9.80665

Lift: L = W × sin A

Drag: D = W × cos A

The program uses the polar-to-rectangular conversion to calculate lift and drag.


HP 32SII Programs: Glide Slope Calculations

Code 1:

Code:
G01  LBL G
G02  DEG
G03  INPUT G
G04  INPUT H
G05  INPUT M
G06  R↓
G07  x<>y
G08  ÷
G09  ASIN
G10  STO A
G11  VIEW A
G12  R↑
G13  9.80665
G14  ×
G15  STO W
G16  VIEW W
G17  θ,r→y,x
G18  STO L
G19  VIEW L
G20  x<>y
G21  STO D
G22  VIEW D
G23  RTN

Bytes: 42.5
Checksum: 4717

Notes:

* This version has prompts and view commands to guide the user. We don't have to preload registers as the INPUT commands guide us.

* All inputs and outputs are stored to variables. 7 variables are used, which will require 56 bytes. On the HP 32SII, each variable that contains non-zero values takes 8 bytes of memory. If you want to make the variables local, insert a CLVARS command for G23 and line G24 becomes RTN.

Variables:

Input:

G = Glide Distance. The distance that glider climbs to it's peak. Think of the hypotenuse of a right triangle. Distance is in meters.

H = Height. The height that the glider reaches. Distance is in meters.

M = Mass. Mass of the glider in kilograms.

Output:

A = Angle. Angle of the of glider's flight in degrees.

W = Weight. Weight of the glider, which is Newtons.

L = Lift force of the glider, in Newtons.

D = Drag force of the glider, in Newtons.

Code 2:

Code 2 is a shorter code which does not store anything into variables. The program starts with G (glide distance), H (height), and M (mass) on the stack.

Code:
L01   LBL L
L02   DEG
L03   R↓
L04   x<>y
L05   ÷
L06   ASIN
L07   STOP  (display A)
L08   R↑
L09   9.80665
L10   ×
L11   STOP  (display W)
L12   θ,r→y,x
L13   RTN    (L is on the x stack, D is on the y stack)

Bytes: 27.5 bytes
Checksum: 6446


Examples

Example 1:
Glider distance: G = 178 m
Height: H = 23 m
Mass of the glider: M = 55 kg

Output:
Angle: A ≈ 7.4241°
Weight: W ≈ 539.3658 N
Lift: L ≈ 534.8441 N
Drag: D ≈ 69.6933 N


Example 2:
Glider distance: G = 200 m
Height: H = 30 m
Mass of the glider: M = 39 kg

Output:
Angle: A ≈ 8.6269°
Weight: W ≈ 382.4594 N
Lift: L ≈ 378.1322 N
Drag: D ≈ 57.3689 N


Source

National Museum of the United States Air Force. "Mathematics of Flight: Glide Slope II" September 2020. Retrieved August 2023.
https://www.nationalmuseum.af.mil/Portal...e%20II.pdf

What do you prefer: (1) programs with prompts and stores the results or (2) programs that uses the stack and saves as much memory as possible?
Visit this user's website Find all posts by this user
Quote this message in a reply
06-16-2024, 04:19 AM
Post: #2
RE: (32SII) Glide Slope Calculations
Wonder if this would work for a 747 with total engine failure.
Find all posts by this user
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 2 Guest(s)