Post Reply 
41CL: Update to OSX3 Problem (maybe)
11-02-2018, 02:36 PM (This post was last modified: 11-02-2018 02:38 PM by burkhard.)
Post: #1
41CL: Update to OSX3 Problem (maybe)
I'm not sure if this is a problem, but it seems like it.
Hopefully not everyone with a 41CL is unterwegs/enroute/in transit to Allschwil right now :-)

I recently did a FLASH update of my v5 41CL to the 180928 ROM level, the latest as of this writing. Everything seemed to work fine, but there are a few oddities I'm not sure are right. It's possible I may have had some of them before, but hadn't spotted them because I put off a really "deep dive" on everything until I did this update to the latest FLASH.

I'll meter my issues out in separate postings to keep things simple(r) and not overwhelm folks.

Problem: With OSX3 installed, if I run CAT 2, I see "8HY" in place of anything that relates to AMC or OSX as the catalog listing rolls by. If I "R/S" at 8HY and hit ENTER, all kinds of encoded characters do a dance and control of the machine seems unrecoverable (even with ON ← reset) unless I take the batteries out for a minute or so.

Investigation Steps
1. I originally noticed this peculiarity with OSX3 on my "main" configuration that employed Library#4, OSX3, YFNX, PWRX, and WARP. Deciding that was a bunch of "power stuff" all in at once, it might be better to isolate things a bit and I reduced to the following more-minimized setup. Everything I am using is from 180928 ROM level.

Page 4: Library#4 R46
Page 7: OSX3
Page 8: YNFZ

Even under this minimal setup, I see the "8HY" issue.

2. Following that, I swapped in YNFX in place of YNFZ just in order to get access to command YCRC (I still see "8HY" on CAT2 with YNFX). I then used YCRC to confirm the CRC checksums for each of the following in FLASH, comparing against the 28 Sep 18 version of mem_ref.pdf on the 41CL site. (This step just verifies that my recent FLASH update didn't install a corrupted version of any of the ROMs in use. All checked OK.
0x120 4LIB -- CRC OK
0x168 OSXB1 -- CRC OK
0x169 OSXB2 -- CRC OK
0x16A OSXB3 -- CRC OK
0x16B OSXB4 -- CRC OK
0x007 YNFZ-4F -- CRC OK
0x00A YNFX-3A -- CRC OK

So everything looks fine.

What's going on here?
•Is seeing "8HY" in CAT2 just "normal"? I don't remember that being the case in the past. My as-delivered prior FLASH dated to May 18.
•Or is there a bug in OSX3 or the new Library 4?

Any thoughts are appreciated.
Find all posts by this user
Quote this message in a reply
11-02-2018, 03:54 PM
Post: #2
RE: 41CL: Update to OSX3 Problem (maybe)
There is a new version of OSX3 in the 181101 release, which will be posted shortly.
That is the most likely source of the problem.
Visit this user's website Find all posts by this user
Quote this message in a reply
11-02-2018, 04:01 PM
Post: #3
RE: 41CL: Update to OSX3 Problem (maybe)
(11-02-2018 03:54 PM)Monte Dalrymple Wrote:  There is a new version of OSX3 in the 181101 release, which will be posted shortly.
That is the most likely source of the problem.

Ahah, I figured after the 180928 ROM was a month old, I would no longer be "a pioneer" !

Thanks, Monte!
Find all posts by this user
Quote this message in a reply
11-04-2018, 06:09 AM (This post was last modified: 11-04-2018 06:10 AM by Ángel Martin.)
Post: #4
RE: 41CL: Update to OSX3 Problem (maybe)
(11-02-2018 02:36 PM)burkhard Wrote:  What's going on here?
•Is seeing "8HY" in CAT2 just "normal"? I don't remember that being the case in the past. My as-delivered prior FLASH dated to May 18.
•Or is there a bug in OSX3 or the new Library 4?

Sorry about your troubles, yes there was a bug in that revision of the OSX3 module - I sent the correction to Monte a few days ago. I can also send you the ROM images via email if you let me know your email address in a PM - so you won't have to wait for the monthly general ROM package update,

ÁM
Find all posts by this user
Quote this message in a reply
11-04-2018, 01:39 PM
Post: #5
RE: 41CL: Update to OSX3 Problem (maybe)
(11-04-2018 06:09 AM)Ángel Martin Wrote:  I can also send you the ROM images via email if you let me know your email address in a PM - so you won't have to wait for the monthly general ROM package update,

ÁM

No need to, the new pkg is available on Monte's site - rom_files_181101.zip.

--Bob Prosperi
Find all posts by this user
Quote this message in a reply
11-04-2018, 01:55 PM
Post: #6
RE: 41CL: Update to OSX3 Problem (maybe)
(11-04-2018 01:39 PM)rprosperi Wrote:  
(11-04-2018 06:09 AM)Ángel Martin Wrote:  I can also send you the ROM images via email if you let me know your email address in a PM - so you won't have to wait for the monthly general ROM package update,

ÁM

No need to, the new pkg is available on Monte's site - rom_files_181101.zip.

I installed today the new update... all looks fine!
Find all posts by this user
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 1 Guest(s)