(25) Calculs Planimetriques en Coordonnees

[SlideRule]

If French is a language you are versed in and have the time/desire to translate a collection of HP-25 programs from French to English, send me a PM. Anyone can start & contribute with a translation of the attached PDF of the target contents.
[attachment=6424]

BEST!
SlideRule

[Thomas Klemm]

Used Google Translate for this one:

Quote:Raccordement parabolique entre 2 paraboles.

The suggestion made me smile:

Quote:Parabolic connection between 2 dishes.

However the 2nd suggestion is more likely what we want:

Quote:Parabolic connection between two parabolas.

---

(10-05-2018 09:09 PM)burkhard Wrote:  Wow, somebody uses "GRAD" mode!

We found the other one:

Quote:

• Raccordement circulaire entre 1 droite and 1 circle.
  • R > 0 et \(\alpha\) < 200^gr ou R < 0 et \(\alpha\) > 200^gr
  • R < 0 et \(\alpha\) < 200^gr ou R > 0 et \(\alpha\) > 200^gr
    

And where are the programs?
Nice handwriting by the way.

Kind regards
Thomas

[SlideRule]

Quote:…And where are the programs?…

My intent is to translate the collection via collaboration with a mother tongue member rather than transliterate via brute force, hence the CONTENTS only posting. If the interest in the programs is pressing, an extant posting will proceed. I was hoping for a PM prior to further action.

I believe my reticence is well expressed in Thomas's reply, thanks for the confirmation.

BEST!
SlideRule

[SlideRule]

Quote:…And where are the programs?…

My intent is to translate the collection via collaboration with a mother tongue member rather than transliterate via brute force, hence the CONTENTS only posting. If the interest in the programs is pressing, an extant posting will proceed. I was hoping for a PM prior to further action.

I believe my reticence is well expressed in Thomas's reply, thanks for the confirmation.

BEST!
SlideRule

ps: OK, check out General Software Library for a partial posting

[PedroLeiva]

(10-09-2018 11:55 AM)SlideRule Wrote:  

Quote:…And where are the programs?…

My intent is to translate the collection via collaboration with a mother tongue member rather than transliterate via brute force, hence the CONTENTS only posting. If the interest in the programs is pressing, an extant posting will proceed. I was hoping for a PM prior to further action.

I believe my reticence is well expressed in Thomas's reply, thanks for the confirmation.

BEST!
SlideRule

I like this initiative for HP25 geometric software, looks very well done. Unfortunately, no numeric examples for the programs presented, this would help translation from French to English. I will file the collection. I wish you good luck and that a collaborator will soon appear. Pedro

[badaze]

Even if I understand each separate word because I’m French I’m not able to understand a whole sentence !


Tabulations de points en X, Y sur une droite sounds to me like a restaurant menu dish name.

[Thomas Okken]

With my high school French, I was able to figure most of it out (from the 1-14.pdf), though without the illustrations I would have been lost. I'm not familiar with French mathematical jargon, but guessed that "droite" is similar to the use of "Gerade" (noun) in German, meaning "straight line."

I can't for the life of me figure out what "gisement" is supposed to mean in this context, though. (Program 4, center of page.) The definitions I find in Wiktionary and elsewhere on-line don't seem to apply.

And I'd never seen the notation

Code:

1 | x
  | y

before. Again from context, it looks like it means "point 1."

[grsbanks]

(10-12-2018 07:06 PM)Thomas Okken Wrote:  I can't for the life of me figure out what "gisement" is supposed to mean in this context, though.

I've never seen it used in this context (and I did 5 years of school in France!) but would guess it means "slope". A straight line (that is indeed what "une droite" is) can be defined by two points or by one point and a slope (or vector for that matter).

[Thomas Klemm]

translates "gisement" to German "die Seitenpeilung" and this in turn to English "relative bearing".

If you look at the code the difference of the coordinates of point 1 and 2 is transformed to polar coordinates.
Thus it's an angle, not a slope. But of course they are related.

HTH
Thomas

[Thomas Okken]

(10-12-2018 11:13 PM)Thomas Klemm Wrote:   translates "gisement" to German "die Seitenpeilung" and this in turn to English "relative bearing".

French Wikipedia agrees: https://fr.wikipedia.org/wiki/Gisement_(navigation)

[SlideRule]

All EIGHT parts are now posted, enjoy.

BEST!
SlideRule

ps: I did the submit the series as a complete PDF for the DVD, etc..

[PedroLeiva]

(11-08-2018 04:41 PM)SlideRule Wrote:  All EIGHT parts are now posted, enjoy.

BEST!
SlideRule

ps: I did the submit the series as a complete PDF for the DVD, etc..

Sorry, I can´t see EIGHT parts of this French programs job. I have downloaded 4 PDF, where are the other four?
Pedro

[SlideRule]

(11-08-2018 04:52 PM)PedroLeiva Wrote:  Sorry, I can´t see EIGHT parts of this French programs job. I have downloaded 4 PDF, where are the other four?
Pedro

Greetings Pedro; there here, the General Software Library, HP Software Libraries, posted as:
(25) 5-of-8 Calcul de Base
(25) 6-of-8 Calcul dune Parabole
(25) 7-of-8 Calculs de Raccordement
(25) 8-of-8 Calcul Relatif aux Profils Travers
sorry for any confusion

BEST!
SlideRule

[PedroLeiva]

(11-08-2018 05:54 PM)SlideRule Wrote:  

(11-08-2018 04:52 PM)PedroLeiva Wrote:  Sorry, I can´t see EIGHT parts of this French programs job. I have downloaded 4 PDF, where are the other four?
Pedro

Greetings Pedro; there here, the General Software Library, HP Software Libraries, posted as:
(25) 5-of-8 Calcul de Base
(25) 6-of-8 Calcul dune Parabole
(25) 7-of-8 Calculs de Raccordement
(25) 8-of-8 Calcul Relatif aux Profils Travers
sorry for any confusion

BEST!
SlideRule

Great, TYVM
Pedro