Post Reply 
[WP-34S] Accessing step
05-22-2014, 06:36 AM
Post: #1
[WP-34S] Accessing step
QQ: Say I have like 100 steps in my program and want to see #57. Is there another way but use up and down arrows?
Find all posts by this user
Quote this message in a reply
05-22-2014, 06:39 AM (This post was last modified: 05-22-2014 06:51 AM by Thomas Klemm.)
Post: #2
RE: [WP-34S] Accessing step
GTO.057
Find all posts by this user
Quote this message in a reply
05-22-2014, 07:05 AM
Post: #3
RE: [WP-34S] Accessing step
(05-22-2014 06:39 AM)Thomas Klemm Wrote:  GTO.057
Nice. Thanks Thomas :-)
Find all posts by this user
Quote this message in a reply
05-22-2014, 09:12 AM
Post: #4
RE: [WP-34S] Accessing step
FYI, please see p. 98 (of 244) of the manual.

d:-)
Find all posts by this user
Quote this message in a reply
05-22-2014, 01:26 PM (This post was last modified: 05-22-2014 01:28 PM by jebem.)
Post: #5
RE: [WP-34S] Accessing step
(05-22-2014 09:12 AM)walter b Wrote:  FYI, please see p. 98 (of 244) of the manual.

d:-)

Sad My manual has got only 211 pages (v3.1)...
Anyhow, that solution only works in input mode, because when in program mode we have to navigate using just the up and down arrows, right?
I do not see this a big issue, however it was nice if we could do page up and page down as well from inside the program editor.

Jose Mesquita
RadioMuseum.org member

Find all posts by this user
Quote this message in a reply
05-22-2014, 02:11 PM (This post was last modified: 05-22-2014 02:46 PM by walter b.)
Post: #6
RE: [WP-34S] Accessing step
(05-22-2014 01:26 PM)jebem Wrote:  
(05-22-2014 09:12 AM)walter b Wrote:  FYI, please see p. 98 (of 244) of the manual.

d:-)

Sad My manual has got only 211 pages (v3.1)...

You don't want me to specify the respective pages for v3.0, v2.2, etc., do you? Wink

(05-22-2014 01:26 PM)jebem Wrote:  Anyhow, that solution only works in input mode, because when in program mode we have to navigate using just the up and down arrows, right?
I do not see this a big issue, however it was nice if we could do page up and page down as well from inside the program editor.

That solution works in run mode. When in program mode, how about pressing [P/R] [GTO][.] xyz [P/R] ?

d:-)

P.S.: And Franz is right.
Find all posts by this user
Quote this message in a reply
05-22-2014, 09:05 PM
Post: #7
RE: [WP-34S] Accessing step
(05-22-2014 02:11 PM)walter b Wrote:  
(05-22-2014 01:26 PM)jebem Wrote:  Sad My manual has got only 211 pages (v3.1)...

You don't want me to specify the respective pages for v3.0, v2.2, etc., do you? Wink
Of course not Smile
I do my home work, so before posting my remark I did check my copy of the freeware pdf downloadable Owner's Guide v3.1.
By the way, the information on the GTO command is on page 87 of 211.

(05-22-2014 02:11 PM)walter b Wrote:  
(05-22-2014 01:26 PM)jebem Wrote:  Anyhow, that solution only works in input mode, because when in program mode we have to navigate using just the up and down arrows, right?
I do not see this a big issue, however it was nice if we could do page up and page down as well from inside the program editor.

That solution works in run mode. When in program mode, how about pressing [P/R] [GTO][.] xyz [P/R] ?

P.S.: And Franz is right.

Well, I checked on my WP-34S before posting, and it didn't work in programming mode for the two times I tried.
For instance, typing [h] + [XEQ] (GTO) [.] [0] [2] [5]
What I did get was two new program entries:
GTO 02
5
And so I wrongly assumed it was not working as indicated.

But now I have found out the issue: as I mentioned in another thread, my calculator has a lot of keyboard issues, so I found out one more failing key: The [.].
So it is the [A], [.], and one full row from [down] to [-].
I believe it is about time to scrap it and get another one Sad

Jose Mesquita
RadioMuseum.org member

Find all posts by this user
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 1 Guest(s)