Threaded Mode | Linear Mode

Sylvain Cote · 08-14-2023, 06:31 PM

Pictures of my beta unit ...

[Image: 82120D_1.jpeg]

aurelio · 08-15-2023, 07:24 PM

:O

Compliments Diego for your creation and thank-you Sylvain for the report and tests

Diego Diaz · 08-16-2023, 07:37 PM

Hi all,

Thanks. Sylvain for these clear pictures. ;-)

and Aurelio for your kind words.

Best.

Diego.

Sylvain Cote · 08-19-2023, 06:12 PM

The battery indicator is finally visible!

It took ...

305 magnetic cards read/write
315 barcode program strips
134h test program execution

... to make it happen.

Diego Diaz · 08-19-2023, 06:22 PM

Hi Sylvain,

And thanks for confirming it works!

I was starting to think that the low battery detection circuit was not properly designed. :-)

Note however that the "BAT" annunciator is activated when the battery capacity is about 22-25%, so there's still some "life" in it, though it is highly advisable to recharge it before it runs under 20% to extend functional life span.

Best wishes.

Diego.

Sylvain Cote · (This post was last modified: 08-25-2023 02:50 PM by Sylvain Cote.)

Test round #2 → 41CL Flash update

Flash upgrade setup

plug serial cable
41CL

Code:

MMUDIS // disable memory management unit MMUCLR // clear memory management unit configuration "YFNX" // CL Extreme ROM PLUG1L // map ROM image to page 8 "YUPS" // CL Update ROM PLUG1U // map ROM image to page 9

Code:

TURBO50 // 50x speed up SERINI // initialize serial port BAUD48 // set speed to 4800 baud MMUEN // enable memory management unit CAT 2 // search for CL Update ROM image : UPDAT 4D
Computer

Code:

java -jar clupdate-1.1.0.jar --update rom_files_230725.zip /dev/tty.usbserial-5230 4800 // HH:MM:SS --update [fileName: rom_files_230725.zip] [portName: /dev/tty.usbserial-5230] // HH:MM:SS File rom_files_230725.zip loading ... done // HH:MM:SS Serial /dev/tty.usbserial-5230 opened at 4800 baud. // HH:MM:SS Waiting for 41CL commands ...
41CL

Code:

ON          // disable sleep CF 26       // disable beeper FDBVER?     // get current Flash revision : ??/??/???? (MDY) "*"         // scan all ROM images CMOPEN      // open serial port communication CPONLY      // do CRC compare only FLCHK?      // scan Flash for outdated ROM images             // HH:MM:SS Report     ? outdated pages, out of 1024 pages, spread over ? Flash blocks, estimated update time: ??h ??m ??s

Code:

CDBVER?     // 07/25/2023 (MDY)    [should be equal or near to rom_files_YYMMDD.zip date value] "*"         // update all ROM images FLUPD       // do the update CDBEXP      // to validate that all ROM images has been updated             // HH:MM:SS Report     0 outdated pages, out of 1024 pages, spread over 0 Flash blocks, estimated update time: 00h 00m 00s FDBVER?     // get current Flash revision : 07/25/2023 (MDY)

Code:

CMCLOSE     // close serial port communication CDBDEL      // delete correlated ROM image MMUDIS      // disable memory management unit MMUCLR      // clear memory management unit configuration OFF         // power off & reactivate sleep mode
unplug serial cable

Flash upgrade to 2023-07-25

Code:

CL Board  :: FDBVER?    :: CDBEXP

41CLv2    :: 09/23/2022 :: Report        7 outdated pages, out of  256 pages, spread over  5 Flash blocks, estimated update time: 00h 16m 01s

41CLv3    :: 09/23/2022 :: Report       15 outdated pages, out of  512 pages, spread over  9 Flash blocks, estimated update time: 00h 29m 33s

41CLv4    :: 09/23/2022 :: Report       15 outdated pages, out of  512 pages, spread over  9 Flash blocks, estimated update time: 00h 29m 33s

41CLv5 #1 :: 09/23/2022 :: Report       73 outdated pages, out of 1024 pages, spread over 19 Flash blocks, estimated update time: 01h 14m 47s

41CLv5 #2 :: 06/03/2023 :: Report        6 outdated pages, out of 1024 pages, spread over  4 Flash blocks, estimated update time: 00h 12m 56s

All my units has been updated and the battery is not depleted.
So I will simulate a lot of update by doing a downgrade/upgrade loop until the BAT light-up between 2023-07-25 and 2018-12-28

Flash downgrade setup

plug serial cable
41CL

Code:

MMUDIS      // disable memory management unit MMUCLR      // clear memory management unit configuration "00A>830"   // 00A YFNX-4C Flash location > 830 free RAM location YMCPY       // copy YFNX-4C from Flash to RAM "062>831"   // 062 YUPS-4D Flash location > 831 free RAM location YMCPY       // copy YUPS-4D from Flash to RAM

Code:

"830-RAM"   // CL Extreme location in RAM PLUG1L      // map YFNX ROM image in RAM to page 8 "831-RAM"   // CL Update location in RAM PLUG1U      // map YUPS ROM image in RAM to page 9

Code:

TURBO50     // 50x speed up SERINI      // initialize serial port BAUD48      // set speed to 4800 baud MMUEN       // enable memory management unit CAT 2       // search for "YFNX 4C" and "UPDAT 4D" ON          // disable sleep CF 26       // disable beeper
loop
- Computer odd step
  
  Code:
  
  java -jar clupdate-1.1.0.jar --update rom_files_181228.zip /dev/tty.usbserial-5230 4800 // HH:MM:SS --update [fileName: rom_files_181228.zip] [portName: /dev/tty.usbserial-5230] // HH:MM:SS File rom_files_181228.zip loading ... done // HH:MM:SS Serial /dev/tty.usbserial-5230 opened at 4800 baud. // HH:MM:SS Waiting for 41CL commands ...
  Computer even step
  
  Code:
  
  java -jar clupdate-1.1.0.jar --update rom_files_230725.zip /dev/tty.usbserial-5230 4800 // HH:MM:SS --update [fileName: rom_files_230725.zip] [portName: /dev/tty.usbserial-5230] // HH:MM:SS File rom_files_230725.zip loading ... done // HH:MM:SS Serial /dev/tty.usbserial-5230 opened at 4800 baud. // HH:MM:SS Waiting for 41CL commands ...
- 41CL
  
  Code:
  
  FDBVER? // get current Flash revision : 07/25/2023 (odd) | 12/18/2018 (even) "*" // scan all ROM images CMOPEN // open serial port communication CPONLY // do CRC compare only FLCHK? // scan Flash for outdated ROM images // HH:MM:SS Report 315 outdated pages, out of 1024 pages, spread over 67 Flash blocks, estimated update time: 04h 40m 59s
  
  Code:
  
  CDBVER? // 12/18/2018 (odd) | 07/25/2023 (even) "*" // update all ROM images FLUPD // do the update CDBEXP // to validate that all ROM images has been updated // HH:MM:SS Report 0 outdated pages, out of 1024 pages, spread over 0 Flash blocks, estimated update time: 00h 00m 00s FDBVER? // get current Flash revision : 12/18/2018 (odd) | 07/25/2023 (even) CMCLOSE // close serial port communication CDBDEL // delete correlated ROM image
end-loop

Code:

MMUDIS // disable memory management unit MMUCLR // clear memory management unit configuration OFF // power off & reactivate sleep mode
unplug serial cable

Testing on my 41CL v5 #2 ...

Code:

  FDBVER?    :: CDBVER?    :: CDBEXP

  07/25/2023 :: 12/18/2018 ::   64 outdated pages, out of 1024 pages, spread over  24 Flash blocks, were updated before the 41CL was send crashing on the floor (no comment)

Switching to my 41CL v4

Code:

  FDBVER?    :: CDBVER?    :: CDBEXP

  07/25/2023 :: 12/18/2018 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

  12/18/2018 :: 07/25/2023 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

  07/25/2023 :: 12/18/2018 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

  12/18/2018 :: 07/25/2023 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

  07/25/2023 :: 12/18/2018 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

  12/18/2018 :: 07/25/2023 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

Switching to my 41CL v3

Code:

  FDBVER?    :: CDBVER?    :: CDBEXP

  07/25/2023 :: 12/18/2018 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

  12/18/2018 :: 07/25/2023 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

  07/25/2023 :: 12/18/2018 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

  12/18/2018 :: 07/25/2023 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

  07/25/2023 :: 12/18/2018 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

  12/18/2018 :: 07/25/2023 ::  123 outdated pages, out of  512 pages, spread over  37 Flash blocks

Switching to my 41CL v5 #1

Code:

  FDBVER?    :: CDBVER?    :: CDBEXP

  07/25/2023 :: 12/18/2018 ::  311 outdated pages, out of 1024 pages, spread over 66 Flash blocks

... the BAT annunciator went on here, but it went off after, so I am continuing the test

  12/18/2018 :: 07/25/2023 ::  311 outdated pages, out of 1024 pages, spread over 66 Flash blocks

  07/25/2023 :: 12/18/2018 ::  311 outdated pages, out of 1024 pages, spread over 66 Flash blocks

... the BAT annunciator went on permanently here after

  12/18/2018 :: 07/25/2023 ::   31 outdated pages, out of 1024 pages, spread over 13 Flash blocks

Final results on a single charge are ...

Code:

FLCHK?

   ~50 x FLDB/CFLDB ROM images downloaded/uploaded to/from RAM 

FLUPD

  2620 x ROM images downloaded to RAM

   725 x 64KiB Flash blocks read/erased/written

edit: last update 2023-08-25 10h50 UTC-4h

Ángel Martin · 08-22-2023, 06:28 AM

Thanks Sylvain for a thorough report. I just picked up my PowerPack from the post office and it is now powering my CL, purring like a wild cat - kudos to Diego, as always!

I was thinking of doing some tests but but you've beat me to it ;-)

it's a great thing not needing to worry about alkaline batteries anymore!

Sylvain Cote · 08-25-2023, 02:53 PM

Test round #2 → 41CL Flash update

Final results on a single charge are ...

Code:

FLCHK?

   ~50 x FLDB/CFLDB ROM images downloaded/uploaded to/from RAM 

FLUPD

  2620 x ROM images downloaded to RAM

   725 x 64KiB Flash blocks read/erased/written

KimH · (This post was last modified: 09-13-2023 01:16 PM by KimH.)

Hi Diego,

Just got my 82120D - works great, I am one happy camper Smile

Thank you for making this - much needed option - available!!

/KimH

PS: Ready for one more if/when you make a second batch

Sylvain Cote · 09-13-2023, 02:33 PM

(09-13-2023 01:11 PM)KimH Wrote: Just got my 82120D - works great, I am one happy camper
Thank you for making this - much needed option - available!!

Same here!

(09-13-2023 01:11 PM)KimH Wrote: PS: Ready for one more if/when you make a second batch

I already have a beta unit, a production unit and three more in the pipeline. (one per production batch)

MeindertKuipers · 09-14-2023, 08:00 AM

Just finished a marathon test with Diego's 82120D (Beta).
Setup: HP41CL with TIME module and the PPC rom plugged. Running PNG (Prime Number Generator) from the PPC manual examples, slightly modified to print the prime with the time indication and testing flag 49 for battery status, print this when BAT is low.
Printing using the YPRT ROM to print into the serial port with a PC connected, printing to the HP82240 simulator in HP82143 mode. Running in TURBO 50 mode all the time with the serial port active.

Running time until BAT appearance: 59 hrs 23 minutes
Running time from BAT until OFF: 12 hrs 28 minutes
Total running time 71 hrs 51 minutes, highest prime found is 455921

Compared with my own built 1100 mAh battery solution: total running time 36 hrs 35 minutes (no BAT indication)

Compliments to Diego for another fine HP41 necessity!

Here is the program used:

Code:

 01◆LBL "PNG"

 02 2

 03◆LBL 01

 04 XROM "NP"

 05 X=Y?

 06 XEQ 02

 07 CLX

 08 2

 09 ST+ Y

 10 GTO 01

 11◆LBL 02

 12 CLA

 13 TIME

 14 FIX 4

 15 ATIME

 16 "Ͱ "

 17 RDN

 18 FIX 0

 19 ARCL X

 20 FS? 49

 21 "Ͱ BAT"

 22 AVIEW

 23 END

Diego Diaz · 09-15-2023, 07:25 PM

Hi Meindert,

Thanks for sharing this test results and your kind words. :-)

Special interest the running time after "BAT" annunciator, which gives an overall idea about the total capacity of the 82120D.

Needless to say that this is a *one time* test and it is always recommended to charge the Power Bank early after the "BAT" is on, to extend the battery life.

All the best from the Caribbean.

Diego.

Uli · 09-17-2023, 05:35 AM

Very interesting information!
Do you also know the Running time until BAT appearance by using LR1 NiMH with each ~ 500mAh in your HP41CL?
I have to change the batteries every 2 weeks. And I am happy to get the new solution from Diego.

+++++++

(09-14-2023 08:00 AM)MeindertKuipers Wrote: Just finished a marathon test with Diego's 82120D (Beta).
Setup: HP41CL with TIME module and the PPC rom plugged. Running PNG (Prime Number Generator) from the PPC manual examples, slightly modified to print the prime with the time indication and testing flag 49 for battery status, print this when BAT is low.
Printing using the YPRT ROM to print into the serial port with a PC connected, printing to the HP82240 simulator in HP82143 mode. Running in TURBO 50 mode all the time with the serial port active.

Running time until BAT appearance: 59 hrs 23 minutes
Running time from BAT until OFF: 12 hrs 28 minutes
Total running time 71 hrs 51 minutes, highest prime found is 455921

Compared with my own built 1100 mAh battery solution: total running time 36 hrs 35 minutes (no BAT indication)

Compliments to Diego for another fine HP41 necessity!

Here is the program used:

Code:

01◆LBL "PNG" 02 2 03◆LBL 01 04 XROM "NP" 05 X=Y? 06 XEQ 02 07 CLX 08 2 09 ST+ Y 10 GTO 01 11◆LBL 02 12 CLA 13 TIME 14 FIX 4 15 ATIME 16 "Ͱ " 17 RDN 18 FIX 0 19 ARCL X 20 FS? 49 21 "Ͱ BAT" 22 AVIEW 23 END

MeindertKuipers · 09-17-2023, 02:09 PM

(09-17-2023 05:35 AM)Uli Wrote: Very interesting information!
Do you also know the Running time until BAT appearance by using LR1 NiMH with each ~ 500mAh in your HP41CL?
I have to change the batteries every 2 weeks. And I am happy to get the new solution from Diego.

I do not have these batteries anymore, and in my setup I do not get a low battery at all. I now exclusively use 2 homebuilt packs of 1100 mAh each (the battery taken from a giveaway USB powerbank) and Diego's new product.